Televes DigiSlot DVB-T modulator, wall mount User Manual download pdf (Page 7)

Setting method just the same, when the display shows them, user just need

swift LEFT and RIGHT key to choose and repressing “ENTER” for con rm.

- Transmission mode

After entering Trans mode, the LCD would show the current working mode.

User can move LEFT/RIGHT key and repress ENTER key to select and con rm.

2K and 8K are the options.

- 2K: when the device works as current mode, the number of current carrier

is 2048.

- 8K: when the device works as current mode, the number of current carrier

is 8192.

- Guard interval

In communications, guard intervals are used to ensure that distinct transmissions

do not interfere with one another. These transmissions may belong to di erent

operators (as in TDMA) or same operator (as in OFDM).

The purpose of the guard interval is to introduce immunity to propagation

delays, echoes and re ections, to which digital data is normally very sensitive.

There are four possible options provided to be selected. They are 1/4, 1/8, 1/16,

1/32. User can shift the LEFT/RIGHT key to select and press ENTER to con rm.

- FEC

Forward Error Correction (FEC) rates include 1/2, 2/3, 3/4, 5/6, and 7/8. After

entering FEC submenu, and the LCD display would shows them, users just need

press LEFT and RIGHT button to choose, and press ENTER button for con rm.

- RF Frequency

The RF output frequency range is from 30 to 1000MHz with 1K stepping. After

entering the RF frequency setting submenu, users the can press LEFT, RIGHT,

UP, and DOWN buttons to adjust the frequency and con rm by press ENTER

button.

- RF out level

The RF attenuation range is from -30~-10dBm (81~97dBμV) with 0.1dB step.

After entering this setting submenu, user can shift UP/DOWN/LEFT/RIGHT key

to set the output level and press ENTER to con rm.

4) IP Output Setting

4.1 IP Output

4.2 Service IP

4.3 Output IP

4.4 Subnet Mask

4.5 Gateway

4.6 Port

User can press “UP/DOWN” to choose this item. “Enter” and “LEFT/RIGHT” to

set the parameters.

If not set the following parameters will be no use, the IP Output will not work.

IP Output

OFF ON

Service IP

192.168.002.137

Output IP

224.002.002.002

Subnet Mask

255.255.255.000

Gateway

192.168.002.000

Port

01234

- IP Output

The IP Output option, must be enable.

- Service IP

The IP Output Port address. The format is xxx.xxx.xxx.xxx (like as 192.168.2.137).

- Output IP

The IP Output data receive address. The format is xxx.xxx.xxx.xxx (like as

224.2.2.2). After set the Output IP address , you must use the new address to

receive IP Output data.

- Subnet Mask

General is 255.255.255.0, it is must the same in a local area network.

- Gateway

If the device is in di erent net segment, you must set the gateway.

- Port

The UDP protocol port (like as 8001), you should use Output IP and new port to

receive IP Output data (like as udp://224.2.2.2:8001).

5) Network setting

After inter network setting, there are three Submenu Items for setting, just

show as the following LCD display pictures.

5.1 IP Address

5.2 Subnet Mask

5.3 Gateway

5.4 MAC Address

5.5 Reset Password

5.6 Web Manage Port

User can press “UP/DOWN” to choose this item. “Enter” and “LEFT/RIGHT” to

set the parameters.

Note: The MAC address is according to the factory setting, and it’s unique. The

display will respectively show as below:

IP Address

192.168.000.136

Subnet mask

255.255.255.000

Gateway

192.168.000.001

MAC Address

201110140940

Reset pasword ?

Yes No

Web Manage Port

00080

6) Save con g

Users enter save con g submenu for saving settings. Choose yes for con rm set.

Save Configuration?

Yes No

Saving config ...

7) Loading con g

At this menu, user can press UP/DOWN key to select and repress ENTER to

con rm. User can restore the device into the last saved con guration by

choosing “7.1” and restore the device into factory con guration by choosing

“7.2” the display will show as below:

7.1 Load Saved CFG

7.2 Load Default

Load Saved CFG ?

Yes No

Loading config ...

Note: In the  rst use of the product, it is recommended to “Load Default” before

starting with the con guration.

8) Version

User can check the hardware version and software version of this equipment

when enter this submenu.

EncoderModulator

SW 5.13b HW 5.0

1 2 3 4 5 6 7 8 9 10 11 12 ... 19 20

Comments to this Manuals

No comments

Televes DigiSlot DVB-T modulator, wall mount User Manual Page 7

Comments to this Manuals

Related products and manuals for TV Accessories Televes DigiSlot DVB-T modulator, wall mount